Special Information - TM-10-3930-253-20P0005

TM 10-3930-253-20P

authorized additional prescribed loads will multiply the

(3) Recoverability code, indicates whether

number of prescribed loads authorized by the quantity of

unserviceable items should be returned for recovery or

repair parts reflected in the appropriate density column,

salvage.

Items not coded are expendable.

applicable to the number of items supported to obtain

Recoverability codes are:

the total quantity of repair parts authorized.

(3) Organizational

units

providing

Code

Explanation

maintenance for more than 100 of these equipments

Applied to repair parts and assemblies which

shall determine the total quantity of parts required by

are economically repairable t DSU and

converting the equipment quantity to a decimal factor by

GSU activities and normally are furnished

placing a decimal point before the next to last digit of

by supply on an exchange basis.

the number to indicate hundredths, and multiplying the

Applied to high dollar value recoverable repair

decimal factor by the parts quantity authorized in the 51-

parts which are subject to special handling

100 allowance column. Example: authorized allowance

and are issued on an exchange basis.

for 51-100 equipments is 40; for 150 equipments

Such repair parts normally are repaired or

multiply 40 by 1.50 or 60 parts required.

overhauled

depot

maintenance

activities.

(4) Subsequent changes to allowances will be

Applied to repair parts specifically selected for

limited as follows: No change in the range of items is

salvage by reclamation units because of

authorized.

If additional items are considered

precious metal content, critical materials,

necessary, recommendation should be forwarded to U.

high dollar value reusable casings or

S. Army Mobility Equipment Command for exception or

castings.

revision to the allowance list. Revisions to the range of

(4) This column also lists, below the SMR

items authorized will be made by this Command based

code an index number for each item in ascending

on engineering experience, demand data, or TAERS

numerical sequence, which is used to locate items in the

information.

publication when the Federal stock number and/or

h. Illustration Column (8). This column is divided

reference number is known.

as follows:

b. Federal Stock Number. This column indicates

(1) Figure Number Column, (8)(a). Indicates

the Federal stock number for the item.

the figure number of the illustration in which the item is

c. Description. This column indicates the Federal

shown.

item name and any additional description of the item

(2) Item Number, Column (8)(b). Indicates

required. A part number or other reference number is

the callout number used to reference the items in the

followed by the applicable 5 digit Federal supply code

illustration.

for manufacturers in parentheses. Material required for

manufacture or fabrication is identified.

Special Information

d. Unit of Issue. This column indicates the unit

a. Repair parts mortality has been based on 3,000

used as a basis for issue, e.g., ea, pr, ft, yd, etc.

hours of operation per year.

e. Quantity Incorporated in Unit Pack. This column

b. Parts which require manufacture or assembly at

indicates the actual quantity contained in the unit pack.

a category higher than that authorized for the installation

f. Quantity Incorporated in Unit. This column

will indicate in the source column the higher category.

indicates the quantity of the item used in the functional

c. The following publication pertain to the lift truck

group.

and its components:

g. Fifteen-Day Organizational Allowance Column

TM 10-3930-253-12

Operator

and

(4) of Section II and Column (7) of Section III and IV.

organizational

(1) The allowance columns are divided into

maintenance manual

four subcolumns. Indicated in each sub column is the

TM 10-3930-253-35

Field

and

depot

quantity of items authorized for the number of

maintenance manual

equipments supported. Items authorized for use as

TM 10-3930-253-35P

DS, GS, and depot

required, but not for initial stockage are identified with

maintenance

repair

an asterisk in the allowance column.

parts and special tools

(2) The

quantitative

allowances

for

list

organizational level of maintenance represents one

LO 10-3930-253-12

Lubrication Order

initial prescribed load for a 15-day period for the number

of equipments supported.

Units and organizations