| |
TM 10-3930-632-24P
F-
Direct support or aviation intermediate is the
lowest level than can do complete repair of the
item.
H-
General support is the lowest level that can do
complete repair of the item.
L-
Specialized repair activity is the lowest level that
can do complete repair of the item.
D-
Depot is the lowest level that can do complete
repair of the item.
Z-
Nonreparable. No repair is authorized.
B-
No repair is authorized. (No parts or special
tools are authorized for the maintenance of a
"B"-coded item.) However, the item may be
reconditioned by adjusting, lubricating, etc., at
the user level.
(3)
Recoverability Code. Recoverability codes
are assigned to items to indicate the disposition action
on unserviceable items. The recoverability code is
entered in the fifth position of the SMR code as follows:
Code
Application/Explanation
Z -
Nonreparable
item.
When
unserviceable,
condemn and dispose of the item at the level of
maintenance shown in the 3d position of the
SMR code.
O-
Reparable item. When uneconomically
reparable, condemn and dispose of the item at
unit maintenance or aviation unit level.
F-
Reparable
item.
When
uneconomically
reparable, condemn and dispose of the item at
the direct support or aviation intermediate level.
H-
Reparable
item.
When
uneconomically
reparable, condemn and dispose of the item at
the general support level.
D-
Reparable item. When beyond lower level repair
capability, return to depot. Condemnation and
disposal of item not authorized below depot
level.
L-
Reparable item. Condemnation and disposal of
item not authorized below specialized repair
activity (SRA).
A-
Item requires special handling or condemnation
procedures because of specific reasons (e.g.,
precious metal content, high dollar value,
critical material, or hazardous material). Refer
toappropriate manuals/directives for specific
instructions.
c.
CAGEC (Column (3)). The Commercial
and Government Entity (CAGE) Code (C) is a 5-digit
alphanumeric code which is used to identify the
manufacturer,
distributor,
or
Government
agency, etc., that supplies the item.
d.
PART NUMBER (Column (4)). Indicates
the primary number used by
the
manufacturer
(individual, company, firm,
corporation,
or
Government activity), which controls the design and
characteristics of the item by means of its engineering
drawings,
specifications
standards,
and
inspection
requirements to identify an item or range of items.
NOTE: When you use an NSN to requisition an item, the
item you receive may have a different part number from
the part ordered.
e.
DESCRIPTION AND USABLE ON CODE
(UOC) (Column (5)). This column includes the following
information:
(1)
The Federal item name and, when
required, a minimum description to identify the item.
(2)
Physical security classification. Not
Applicable.
(3)
Items that are included in kits and sets
are listed below the name of the kit or set on Figure KIT.
(4)
Spare/repair parts that make up an
assembled item are listed immediately following the
assembled item line entry.
(5)
Part numbers for bulk materials are
referenced in this column in the line item entry for the
item to be manufactured/fabricated.
(6)
When the item is not used with all
serial numbers of the same model, the effective serial
numbers are shown on the last line(s) of the description
(before UOC). Not Applicable.
(7)
The usable on code, when applicable
(see paragraph 5, Special Information).
(8)
In the Special Tools List section, the
basis of issue (BOI) appears as the last line(s) in the
entry for each special tool, special TMDE, and other
special support equipment. When density of equipments
supported exceeds density spread indicated in the basis
of
issue,
the
total
authorization
is
increased
proportionately.
(9)
The statement "END OF FIGURE"
appears just below the last item description in Column 5
for a given figure in both Section II and Section III.
f.
QTY (Column (6)). The QTY (quantity per
figure column) indicates the quantity of the item
3
|