Click here to make tpub.com your Home Page

Page Title: TM-10-3930-622-14

• TECHNICAL MANUAL
• TECHNICAL MANUAL - continued
• Operator's, Organizational, DS, and GS, Maintenance Manual
• Operator's, Organizational, DS, and GS, Maintenance Manual - continued
• Reporting of Errors and Recommending Improvements
• Figure 5-7. Cutout relay.
• Generator Regulator Testing
• Figure 5-7.1. Test equipment for adjusting cutout relay closing voltage.
• Figure 5-7.2. Adjusting cutout relay closing voltage.
• Figure 5-8.1. Test equipment for checking and adjusting voltage regulator.
• Figure 5-8.2. Adjusting voltage regulator.
• Figure 5-9.1. Test equipment for checking current regulator setting.
• Figure 5-9.2. Adjusting current regulator setting.
• Installation
• Figure 6-16.1. Inching and brake - clutch adjustment.
• Appendix A. REFERENCES
• Appendix A. REFERENCES - continued
• Distribution
• Operator's, Organizational, DS, and GS Maintenance Manual
• Distribution
• Appendix C. BASIC ISSUE ITEMS LIST AND ITEMS TROOP INSTALLED OR AUTHORIZED
• Section III. ITEMS TROOP INSTALLED OR AUTHORIZED LIST
• Operator, Organizational, Direct Support and General Support Maintenance Manual
• Table 3-1. Maintenance and Operating Supplies
• Table Of Contents
• Section I. INTRODUCTION AND GENERAL DESCRIPTION
• FUEL SYSTEM.
• Regulator
• BRAKE SYSTEM.
• STEERING MECHANISM.
• FRAME
• Section II. TABLE OF SPECIFICATIONS
• TABLE 2-1. TABLE OF SPECIFICATIONS
• TABLE 2-1. TABLE OF SPECIFICATIONS - continued
• TABLE 2-1. TABLE OF SPECIFICATIONS - continued
• Figure 2-1. Vehicle Dimensions
• TABLE 2-2. TORQUE VALUES
• Section III. PREPARATION FOR USE
• Engine Oil
• Transmission
• Section IV. OPERATION
• POWER AXLE ASSEMBLY.
• Accelerator Pedal
• OPERATION
• PICKING UP LOAD.
• STOPPING TRUCK.
• SAFETY RULES FOR TRUCK OPERATORS.
• Section V. SERVICE INSPECTION, MAINTENANCE, LUBRICATION AND TROUBLE SHOOTING
• VEHICLE APPEARANCE.
• FUEL SYSTEM.
• STARTING AND CHARGING SYSTEM
• TRANSMISSION ASSEMBLY.
• STEERING CYLINDER ASSEMBLY.
• UPRIGHT ASSEMBLY.
• STEERING
• FUEL SYSTEM.
• FILL 'SYSTEM
• Figure 5-4. Contact Gap Adjustment
• STARTING AND CHARGING SYSTEM.
• Figure 5-8. Voltage Regulator Test Setup
• Figure 5-11. Battery Test
• Figure 5-12. Steering Linkage Adjustment
• Figure 5-13. Lubrication Chart (Sheet 1 of 3)
• Figure 5-13. Lubrication Chart (Sheet 2 of 3)
• BLEEDING SERVICE BRAKE SYSTEM
• TROUBLE-SHOOTING.
• TROUBLE-SHOOTING
• TROUBLE-SHOOTING - continued
• TROUBLE-SHOOTING - continued
• TROUBLE-SHOOTING - continued
• TROUBLE-SHOOTING - continued
• TROUBLE-SHOOTING - continued
• TROUBLE-SHOOTING - continued
• Setion VI. REPAIR INSTRUCTIONS
• SURFACE PREPARATION
• DIFFERENTIAL ASSEMBLY.
• Figure 6-1. Front Axle, Exploded View
• Figure 6-2. Differential, Exploded View
• STEERING AXLE.
• Figure 6-3. Differential Adjustment Test Indications
• Figure 6-4. Drive Wheel Disassembly
• Rear tire removal.
• Installation
• Figure 6-8. Parking Brake, Partly Exploded View
• Figure 6-9. Wheel Brake Assembly, Exploded View
• Wheel cylinder disassembly and inspection.
• Figure 6-11. Steering Gear Removal, Exploded View
• Lash adjustment
• Ball nut assembly.
• Adjustment on bench.
• Figure 6-12. Steering Linkage
• Figure 6-13. Control Valve Disassembly
• Inspection.
• Cylinder reassembly.
• PROPELLER SHAFT.
• TRANSMISSION.
• TABLE 6-1. TRANSMISSION PRESSURES
• Figure 6-16. Transmission, Exploded View
• Assembly.
• Disassembly.
• HYDRAULIC LIFT CHAIN.
• Assembly.
• Disassembly.
• Cleaning, inspection, and repair.
• Reassembly.
• Disassembly
• Figure 6-19. Mast Column, Exploded View
• Figure 6-20. Wiring Diagram
• Cleaning.
• INSTRUMENT CLUSTER REMOVAL AND DISASSEMBLY.
• Field frame.
• DISTRIBUTOR.
• Figure 6-21. Distributor, Cap Removed
• Installation.
• OIL PUMP.
• Figure 6-23. Engine Oil Filter, Exploded View
• EXHAUST SYSTEM.
• Repair.
• Testing.
• Disassembly.
• Figure 6-26. Fuel Tank Removal
• Removal.
• ENGINE.
• Figure 6-29. Ignition Timing
• Vacuum test.
• Figure 6-30. Engine Removal Check Points (Sheet 1 of 2)
• Figure 6-30. Engine Removal Check Points (Sheet 2 of 2)
• VALVE COVER
• CAMSHAFT, GEAR AND BEARINGS.
• Assembly and installation.
• Figure 6-33. Piston and Rod Assembly
• Figure 6-36. Measuring Ring End Gap
• CRANKSHAFT AND BEARINGS.
• CYLINDER BLOCK.
• VALVES.
• Figure 6-40. Valve Installation
• Figure 6-41. Checking Rotator Cap Clearance
• Appendix A. REFERENCES
• Appendix B. MAINTENANCE ALLOCATION CHART
• Explanation of Columns in Section II
• SECTION II. MAINTENANCE ALLOCATION CHART
• SECTION II. MAINTENANCE ALLOCATION CHART - continued
• SECTION II. MAINTENANCE ALLOCATION CHART (Cont'd)
• SECTION II. MAINTENANCE ALLOCATION CHART (Cont'd)
• SECTION II. MAINTENANCE ALLOCATION CHART (Cont'd)
• SECTION II. MAINTENANCE ALLOCATION CHART (Cont'd)
• SECTION II. MAINTENANCE ALLOCATION CHART (Cont'd)
• Appendix C. BASIC ISSUE ITEMS LIST
• Maintenance code
• Explanation of Columns in the Tabular List of Maintenance and Operating Supplies - Section III.
• SECTION II. BASIC ISSUE ITEMS
• Section III. MAINTENANCE AND OPERATING SUPPLIES
• Section III. MAINTENANCE AND OPERATING SUPPLIES
• Blank Page
• TM-10-3930-622-14
• Distribution
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS