Click here to make tpub.com your Home Page

Page Title: TM-10-3930-618-34

• TECHNICAL MANUAL
• Direct Support and General Support Maintenance Manual
• Distribution
• Direct Support and General Support Maintenance Manual
• Table 1-3. Engine Fits, Tolerances, and Wear Limits.
• Table 1-3. Engine Fits, Tolerances, and Wear Limits. - continued
• Table 1-3. Engine Fits, Tolerances, and Wear Limits. - continued
• Table 1-3. Engine Fits, Tolerances, and Wear Limits. - continued
• Table 1-3. Engine Fits, Tolerances, and Wear Limits. - continued
• Table 1-3. Engine Fits, Tolerances, and Wear Limits. - continued
• Table 1-4. Transmission Fits, Tolerances, and Wear Limits
• Table 1-5. Miscellaneous Fits, Tolerances and Wear Limits.
• Figure 3-6.1. Counterweight, installed view.
• Figure 3-6.2. Radiator, installed view.
• Figure 3-6.3. Drain valve, radiator.
• Figure 3-20.1. Adjusting valve clearance.
• Figure 5-8.1. Power steering cylinder, installed view.
• Hand Brake Lever, Cable and Linkage
• Brake Master Cylinder
• INDEX
• INDEX - continued
• DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL
  • Missing Page
• LIST OF ILLUSTRATIONS
• LIST OF ILLUSTRATIONS - continued
• Chapter I. INTRODUCTION
• Table 1-2. General Torque Values (Foot-pounds torque)
• Chapter 2. DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
• Table 2-1. Troubleshooting
• Table 2-1. Troubleshooting - continued
• Table 2-1. Troubleshooting - continued
• Table 2-1. Troubleshooting - continued
• Power Plant
• Figure 2-1. Transmission assembly removal and installation.
• Figure 2-2. Torque converter removal and installation.
• Transmission Installation.
• Figure 2-4. Hydraulic pump removal and installation.
• Figure 2-5. Hydraulic lift assembly removal and installation.
• Tilt Cylinders
• Figure 2-7. Hydraulic control valve removal and installation.
• Figure 2-8. Steering axle assembly, removal and installation.
• Drive Axle Assembly
• Figure 2-9. Drive axle assembly removal and installation.
• Installation.
• Chapter 3. REPAIR OF POWER PLANT
• Inspect and Repair.
• Stator
• Diode replacement
• Figure 3-5. Checking alternator output.
• Figure 3-6. Starter motor, disassembly and reassembly/
• Section II. REPAIR OF COOLING SYSTEM
• Section III. REPAIR OF ENGINE FUEL SYSTEM
• Assembly
• Adjustment and Installation
• Figure 3-7. Carburetor disassembly.
• Governor
• Figure 3-8. Governor disassembly.
• Fuel Tank
• Section IV. REPAIR OF ENGINE LUBRICATION SYSTEM
• Figure 3-10. Oil pan removal and installation.
• Figure 3-11. Oil pump.
• Figure 3-12. Checking oil pump radial clearance.
• Figure 3-13. Positioning drive gear offset slot.
• Section V. REPAIR OF TORQUE CONVERTER AND PUMP
• Figure 3-15. Checking pump and converter pressure.
• Table 3-2. Clutch Oil Pressures (Free Running)
• Figure 3-19. Torque converter and pump assembly, disassembly, and reassembly.
• Section VI. REPAIR OF TRANSMISSION
• Figure 3-20. Transmission.
• Figure 3-22. Forward reverse disc assembly.
• Figure 3-23. Transmission control valve.
• Figure 3-24. Single speed transmission disassembly (sheet 1 of 2)
• Figure 3-24. Single speed transmission disassembly (sheet 2 of 2)
• Figure 3-25. Reverse gear and shaft, removal and installation.
• Cleaning, Inspection, and Repair
• Transmission gear train.
• Figure 3-28. Brake pedal (sheet 1 of 2)
• Section VII. REPAIR OF ENGINE
• Cylinder head service
• Figure 3-30. Cylinder head and valves.
• Figure 3-31. Sequence for cylinder head Capscrew tightening.
• Cleaning and Inspection of Cylinder Block
• Figure 3-32. Cylinder block.
• Crankshaft, Main Bearings, Gear, and Pulley
• Figure 3-33. crankshaft gear and pulley.
• Figure 3-35. Piston and connecting rod.
• Connecting Rod Inspection.
• Assembly.
• Figure 3-36. Intake and exhaust valve assembly.
• Figure 3-37. Valve operating mechanism and camshaft.
• Removal, Inspection, and Installation of Valve Springs
• Valve and Valve Seat Grinding.
• Camshaft bearings.
• Figure 3-38. Camshaft bearing installation.
• Figure 3-40. Timing gear cover and rear support.
• Installation.
• Chapter 4. REPAIR OF HYDRAULIC SYSTEM
• Assembly
• Figure 4-1. Hydraulic pump disassembly and reassembly.
• Installation
• Figure 4-2. Hydraulic control valve.
• Section II. REPAIR OF HYDRAULIC LIFT CYLINDERS
• Cleaning and Inspection.
• Figure 4-4. Tilt cylinder.
• Cleaning and Inspection.
• Section III. REPAIR OF LIFT MAST
• Figure 4-6. Hydraulic lift mast.
• Carriage and Backrest
• Figure 4-7. Hydraulic lift carriage and backrest.
• Chapter 5. REPAIR OF FRONT AND REAR AXLE ASSEMBLIES
• Figure 5-1. Steering gear assembly removal and installation (sheet 1 of 2).
• Figure 5-1. Steering gear assembly removal and installation (sheet 2 of 2).
• Figure 5-2. Steering gear assembly.
• Figure 5-3. Checking control spool rotation.
• Mounting Plate.
• Assembly and Adjustment.
• Figure 5-6. Drive-gear alinement.
• Cleaning and Inspection.
• Cleaning and Inspection.
• Power Steering Cylinder
• Figure 5-8. Power steering cylinder with yoke.
• Assembly.
• Figure 5-9. Steer wheel and bearings, removal and installation.
• Figure 5-10. String axle and tie rods.
• Assembly.
• Section II. REPAIR OF BRAKE SYSTEM
• Figure 5-12. Hand brake assembly.
• Figure 5-13. Wheel brake assembly (sheet 1 of 2).
• Figure 5-13. Wheel brake assembly (sheet 2 of 2).
• Figure 5-15. Master cylinder.
• Wheel Cylinders
• Section III. REPAIR OF DRIVE AXLE
• Inspection and Repair.
• Figure 5-18. Drive axle assembly.
• Figure 5-19. Drive axle housing and differential.
• Section IV. REPAIR OF UNIVERSAL JOINT
• Figure 5-20. Universal joints.
• Appendix A. REFERENCES
• INDEX
• TM-10-3930-618-34
• RECOMMENDED CHANGES TO EQUIPMENT TECHNICAL PUBLICATIONS
• Blank Page
• Distribution