FOR OPERATION OF EQUIPMENT PROTRACTED COLD TEMPERATURES BELOW 150F (-260C)

NOTES:

1. FOR

OPERATION

EQUIPMENT

and transmission in neutral, add oil to bring oil level to

PROTRACTED COLD TEMPERATURES BELOW -

"FULL" mark. Operate for 5 minutes and check for

150F (-260C). Remove lubricants prescribed in Key for

leaks.

temperatures above -150F (-260C). Relubricate with

lubricants specified in Key for temperatures below -150F

7. TRANSMISSION AND TORQUE CONVERTER OIL

(-260C). If OEA lubricant is required to meet the

FILTER. Each 1000 hours, remove filter, clean filter

temperature ranges prescribed in the Key, OEA lubricant

mount, and install new filter and seal. Fill transmission to

is to be used in place of OE/HDO-10 lubricant for all

low mark. With engine running at idle speed, oil at

temperature ranges where OE/HDO-10 is specified in

operating temperature and transmission in neutral, add

the Key.

oil to bring oil to "FULL" mark. Operate for 5 minutes

and check filter for leaks.

2. OIL CAN POINTS. Each 250 hours lubricate shift

linkage, control valve linkage, brake linkage, and all

8. HYDRAULIC OIL FILTER.

Each 1000 hours,

exposed adjusting threads with OE/HDO.

remove element, clean filter shell and install new

element. After replacement, operate hydraulic system

3. ENGINE OIL LEVEL HOT OR COLD CHECK. Cold

for 5 minutes, check for leaks, check level and bring to

engine, oil level should be at high mark on dipstick. Hot

"FULL" mark.

engine, oil level must be between high and low marks on

dipstick (allow to set 5 minutes before checking).

9. DISTRIBUTOR. Each 500 hours, lubricate rotor

wick with 3 or 4 drops of OE/HDO 10. Apply very light

4. ENGINE. Oil is to be changed each 250 hours.

coat of GAA to breaker cam.

Drain when lubricant is warm.

10. WHEEL BEARINGS. Each 1000 hours, remove

5. ENGINE OIL FILTER. Each 250 hours, remove filter

wheels, inspect all parts, replace damaged or worn parts,

element, clean housing and Install new filter element.

repack bearings, and assemble.

After Installing new filter element, fill crankcase, operate

engine for 5 minutes, check housing for leaks, check

11. AIR CLEANER. Fork Lift Model MHE-209 has oil

crankcase oil level and bring to "FULL" mark.

bath type air cleaner.

Each 10 hours refill air reservoir to level mark. Each 50

6. TRANSMISSION AND TORQUE CONVERTER.

hours disassemble entire unit, clean, re-oil and

Check level each 50 hours with engine running at idle

assemble.

speed, oil at operating temperature and transmission in

neutral. Maintain oil level at "FULL" mark. Change oil

Fork Lift Model MHE-224 has dry type air cleaner. Each

each 1000 hours. Access to torque converter drain plug

250 hours replace element.

Is gained through timing cover opening on engine

flywheel housing. Rotate flywheel until drain plug Is in

12. HYDRAULIC RESERVOIR FILL AND LEVEL CAP.

opening, remove plug and rotate flywheel until plug

Fork Lift Model MHE-209, remove floor plate to check oil

opening is aligned with drain opening at bottom of

level.

flywheel housing. Fill transmission to low mark. Run

engine at idle speed to fill converter and lines. With

Fork Lift Model MHE-224, open door on floor plate to

engine running at idle speed, oil at operating temperature

check oil level.

13. TRANSMISSION AND TORQUE CONVERTER FILL

AND LEVEL CAP. Fork Lift Model MHE-209, remove

floor plate to check oil level.

TA 219935

LO 10-3930-621-21

CARD 6 OF 7