 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 engine running, oil at operating temperature, and
NOTES:
transmission in neutral (to fill lines and converter), add oil
1. FOR
OPERATION
OF
EQUIPMENT
IN
to bring to "FULL" mark. Operate for five minutes and
PROTRACTED COLD TEMPERATURES BELOW-15F
check for leaks.
(-260C).
Remove lubricants prescribed in Key for
9. HYDRAULIC RESERVOIR FILTER.
temperatures above -15F (-260C). Relubricate with
Each 1000 hours, remove element, clean filter shell and
lubricants specified in Key for temperatures below -150F
install new element.
After replacement, operate
(-260C). If OEA lubricant is required to meet the
hydraulic system for 5 minutes, check for leaks, check
temperature ranges prescribed in the Key, OEA lubricant
level and bring to "FULL" mark.
is to be used in place of OE/HDO-10 lubricant for all
10. WHEEL BEARINGS. Each 1000 hours, remove
temperature ranges where OE/HDO-10 is specified in
wheels, inspect all parts, replace damaged or worn parts,
the Key.
repack bearings, and assemble.
2. OIL CAN POINTS. Each 250 hours lubricate throttle
11. DRIVE AXLE. Check level each 250 hours. Change
linkage, and all exposed adjusting threads with OE/HDO.
gear lubricant each 1000 hours. After refill, operate for
3. ENGINE OIL LEVEL HOT OR COLD CHECK. Cold
five minutes, check for leaks and bring oil level to level
engine, oil level should be at high mark on dipstick. Hot
plug opening.
engine, oil level must be between high and low marks on
12. LUBRICANTS. The following is a list of lubricants
dipstick (allow to set 5 minutes before checking).
with military symbols and applicable specification
4. ENGINE. Oil is to be changed each 200 hours.
numbers.
Drain when lubricant is warm.
5. ENGINE OIL FILTER. Each 250 hours, remove filter
OE/HDO
MIL-L-2104
element, clean housing and install new filter element.
GO
MIL-L-2105
After installing new filter element, fill crankcase, operate
GAA
MIL-G-10924
engine for 5 minutes, check housing for leaks, check
OEA
MIL-L-46167
crankcase oil level and bring to "FULL" mark.
BFS
MIL-B-46176
6. DISTRIBUTOR. Each 500 hours use one drop of
(SD), Type II
P-D-680
OE/HDO oil on breaker lever pivot and on felt wick under
GGP
MIL-G-23549
rotor. Each 500 hours lightly coat cam with GAA and
lubricate shaft sparingly through lube fitting.
Copy of this Lubrication Order will remain with the
7. AIR CLEANER. Each 10 hours, refill reservoir to
equipment at all times, instructions contained herein are
level mark. Each 50 hours disassemble entire unit,
mandatory.
clean, re-oil and assemble.
8. TRANSMISSION
AND
TRANSMISSION
OIL
By order of the Secretary of the Army:
FILTER. Check level each 10 hours with engine running
at idle speed, oil at operating temperature and
JOHN A. WICKHAM, JR.
transmission in neutral. Maintain oil at "FULL" mark. Oil
General, United States Army
and oil filter element are to be changed each 1000 hours.
Chief of Staff
Remove filter element, clean filter housing, install new
filter element and seal.
After replacement, fill
OFFICIAL:
transmission
to
low
mark.
with
ROBERT M. JOYCE
Major General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-25A,
Operator and Organizational maintenance requirements
for Fork Lift Trucks.
TA220095
LO 10-3930-607-12
*U.S.GOVERNMENT PRINTING OFFICE: 1984-420-903/220
CARD 6 OF 6
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals