TM 10-3930-671-24 Subject, Section(s) Subject, Section(s) General Data, 5.11 No-Load Test Diagnosis, 6.12 General Information, 4.14 Oil and Filter Change Procedures, 4.1 General Maintenance, 11.1 Oil Change Frequency, 4.1 General Precautions, 1.0 Oil Filter Maintenance, 10.1 General Procedures, 4.5, 4.8, 5.1 Oil Level Check Procedures, 4.1 Governor Adjustment, 4.10 Oil Pump, Oil Pan, 4.13 Horn Button & Steering Wheel Disassembly, 9.3 On-Vehicle Troubleshooting, 6.12 Horn Button & Steering Wheel Reassembly, 9.3 Operating Instructions, 4.14 Hydraulic Brake & Inching Lines, 8.4 Operational Tests - Test Drive, 3.2 Hydraulic Brake Fluid and Bleeding Precautions, 8.5 Parking Brake Linkage, 8.1,8.4 Hydraulic Oil Filter and Base Assembly Parts, 10.1 Parts Inspection, 5.11, 9.4, 9.12 Hydraulic Sump and Filter Installation, 10.1 Parts Inspection and Cleaning, 6.16 Hydraulic Sump Fluid Level Check, 10.1 Parts Nomenclature, 7.6, 9.13 Hydraulic System Fluid and Filter Change, 10.1 Planned Maintenance (PM), 3.1 Hydraulic System Relief Pressure Specifications, 10.2 PM Program, 3.2 Hydraulic System Schematic Diagram, 10.0 PM Service Intervals, 3.1 Hydraulic Valve Relief Pressure Settings, 10.6 Powershift Transmissions, 7.2 Idle Speed Adjustment, 4.10 Preliminary Checks, 4.3 Inching Troubleshooting Guide, 8.4 Preliminary Service Preparation, 4.5 Index, 4.14 Preparation For Disassembly, 9.12, 9.13, 10.6 Injection Pump, 5.3 Pressure Bleeding Procedure, 8.5 Injection Pump Overhaul, 5.3 Pressure Specifications, 7.3 Inspection, 7.5 Pressure Test Procedure, 7.3 Inspection, 9.13 Preventive Maintenance, 4.14 Installation & Timing a New Fuel Injection Pump, 5.3 Primary Lift Cylinder-TSU Upright, 13.3 Intake and Exhaust Manifold, Gaskets, 4.13 Priming The Fuel System, 5.3 Lift and Tilt Lines, 10.0 Pump Installation, 10.3 Lift Chain Maintenance, 13.1 Pump Removal, 10.3 Lift Chain-TSU Upright, 13.3 Pump Specifications, 10.3 Lift Cylinder Piping-TSU Upright, 13.3 Pump Troubleshooting, 10.3 Lift Speeds, 2.1 Raising Drive Wheels Off Floor, 3.3 Lifting And Jacking Points, 3.3 Raising Entire Truck, 3.3 Limits and Clearance Data, 4.14 Raising Rear Of Truck, 3.3 Lubricant Specifications, 2.1 Raising Truck With A Hoist, 3.3 Lubrication, 4.14 Reassembly, 5.11,7.5, 9.13,10.6 Lubrication, Fluids and Filters, 3.2 Recommended PM and Lubrication Schedule, 3.1 Main Hydraulic System, 2.1 Reinstalling &Timing the Main Hydraulic System - Description & Operation, 10.0 Original fuel Injection Pump, 5.3 Main Hydraulic Valve Assembly Parts, 10.6 Relief Pressure Adjustment, 10.2 Main Pump Mounting Installation, 10.3 Relief Pressure Check &Adjustment Procedure, 10.2 Main Hydraulic Valve Installation, 10.5 Relief Pressure Setting Check, 9.1 Main Hydraulic Valve Mounting & Control Linkage, 10.5 Relief Pressure Setting Check, 10.2 Main Hydraulic Valve Removal, 10.5 Repair and Replacement, 7.5 Maintenance - General, 12.1 Rocker Cover, Cylinder Head & Gasket, 4.13 Manual Bleeding Method - Inching Circuit, 8.5 Safe Maintenance Practices, 1.0 Manual Bleeding Method - Service Brake Circuit, 8.5 Safety and Operational Checks, 3.1 Maximum Fork Drift, 2.1 Safety Signs and Messages, 1.0 Model Designation, 1.0 Service Brake Adjustment, 7.6 Model Nomenclature, 1.0 Service Brake Adjustment, 8.4 Model Serial Number Code, 1.0 Service Specifications, 2.1 Mounting, 9.5 Shipping Tiedown Instructions, 3.3 Specifications, 6.16 Specifications, 7.6 F-527