Click here to make tpub.com your Home Page

Page Title: WHEEL BEARINGS AND JACKSHAFT BEARINGS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

TM 10-3930-644-14&P
The SAE grade 10 SE engine oil is available at all major
F. WHEEL BEARINGS AND JACKSHAFT BEARINGS
oil companies and most local service stations. The oil
meets the requirements of the American Petroleum
Lubricate with high quality. Grade 2 lithium base grease
Institute and contains rust and oxidation inhibitors, anti-
(characterized by the word "Moly") that contains a
wear ingredients, and an anti-foaming agent.
maximum of 5% micronized molybdenum disulfide.
Lubricant must be waterproof and heat resistant.
If the hydraulic system oil is stored in large containers.
the  storage  containers  must  be  kept  free  of
G.
PRESSURE GUN FITTINGS AND UNIVERSAL
contaminants.  such as dirt., water, and metal chips.
JOINT
Contaminated hydraulic oil is the major cause of
hydraulic system failures. It is recommended that each
Lubricate with a high quality chassis lubricant, N.L.G.I.
storage container be clearly marked FOR USE in
Grade 2 heavy duty sodium base grease available from
HYDRAULIC SYSTEM ONLY.
any reputable oil company.
C. POWER SHIFT TRANSMISSION OIL
H. OIL CAN POINTS
Use a good quality type "A" or suffix "A" automatic
Lubricate all points with SAE 10 or 20 engine oil.
transmission fluid available from any major oil company.
L. BRAKE MASTER CYLINDER
D. DIFFERENTIAL.
STANDARD
SHIFT
TRANSMISSION,
PLANETARY
GEAR,
AND
Use only premium quality, heavy duty brake fluid with an
STEERING GEAR OIL
extreme  heat-cold  range  that  conforms  to  SAE
specification J1703C.
Lubricate these assemblies with SAE 90 EP (extreme
pressure) gear oil which is non-corrosive and resists
J. MASTS
oxidation and foaming. It should have a low pour point
to ensure quick lubrication at either high or low
Lubricate all sliding surfaces of mast uprights with a high
temperatures.
quality. Grade 2 lithium base grease (characterized by
the word '"Moly') that contains a maximum of 5%
E. BULL GEAR AND JACKSHAFT PINION
micronized molybdenum disulfide.  Lubricant must be
waterproof and heat resistant.
Lubricate with high quality, Grade 2 lithium base grease
(characterized by the word "Moly")  that contains a
maximum of 5% micronized molybdenum disulfide.
Lubricant must be waterproof and heat resistant.
TOPIC 2. FUEL RECOMMENDATIONS (GASOLINE AND L.P. GAS)
A. GENERAL
Low-lead and no-lead gasoline, from a reputable
oil manufacturer, are acceptable for a lift truck
Depending upon the owner's selection, the carburetors
equipped with a low emission engine. However,
offered for the engine are designed for either gasoline or
the low emission engine will still be low in
liquid petroleum gas carburetion.
emissions, regardless of whether a leaded or
unleaded gasoline is used.
1. Gasoline
2. Liquid Petroleum Gas
For economy and performance on gasoline
units, it is recommended that a good regular
Liquid petroleum fuel is a gas and is only in the
grade of gasoline with an octane .rating of 89 or
liquid state when under pressure or extreme low
higher be used. The gasoline should meet the
temperature.  When released from the tank it
requirements of .ASTM-D357-61 (motor method)
vaporizes rapidly forming a gas that us heavier
and/or ASTM-D-908-61 research method).
than air.
2-117

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business