| |
SECTION I
TM 10-3930-615-24P
(5)
Part numbers for bulk materials are
referenced in this column in the line item entry for the
item to be manufactured/fabricated.
(6)
When the item is not used with all serial
numbers of the same model, the effective serial
numbers are shown on the last line(s) of the description
(before UOC). Not applicable.
(7)
The usable on code, when applicable (see
paragraph 5, Special information).
(8)
In the Special Tools List section, the basis
of issue (BOI) appears as the last line(s) in the entry for
each special tool, special TMDE and other special
support equipment. When density of equipment's
supported exceeds density spread indicated in the basis
of issue, the total authorization is increased
proportionately.
(9)
The
statement
"END
OF
FIGURE"
appears just below the last item description in Column 5
for a given figure in both Section II and Section III.
f.
QTY (Column (6)). The QTY (quantity per
figure column) indicates the quantity of the item used in
the breakout shown on the illustration figure, which is
prepared for a functional group, subfunctional group or
an assembly. A "V" appearing in this column in lieu of a
quantity indicates that the quantity is variable and the
quantity may vary from application to application.
4. Explanation of Columns (Section IV).
a.
NATIONAL STOCK NUMBER (NSN) INDEX.
(1)
NUMBER column. This column lists
the NSN by National item identification number (NIIN)
sequence. The NIIN consists of the last nine
NSN
digits of the NSN (i.e., 5305-01-674-1467)
NIIN
When using this column to locate an item, ignore the
first 4 digits of the NSN. However, the complete NSN
should be used when ordering items by stock number.
(2)
FIG. column. This column lists the
number
of
the
Figure
where
the
item
is
identified/located. The figures are in numerical order in
Section II and Section Ill.
(3)
ITEM column. The item number identifies
the item associated with the figure listed in the adjacent
FIG. column. This item is also identified by the NSN
listed on the same line.
b.
PART NUMBER INDEX. Part numbers in this
index
are
listed
by
part
number
in
ascending
alphanumeric sequence (i.e., vertical arrangement of
letter and number combination which places the first
letter or digit of each group in order A through Z,
followed by the numbers 0 through 9 and each following
letter or digit in like order.)
(1)
CAGEC column. The Commercial And
Government Entity (CAGE) Code (C) is a 5 digit
alphanumeric code used to identify the manufacturer,
distributor or Government agency, etc., that supplies the
item.
(2)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation or Government activity), which controls
the design and characteristics of the item by means of
its engineering drawings, specifications standards, and
inspection requirements to identify an item or range of
items.
(3)
STOCK NUMBER column. This column
lists the NSN for the associated part number and
manufacturer identified in the PART NUMBER and
CAGEC columns to the left.
(4)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Section II and Ill.
(5)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
c.
FIGURE AND ITEM NUMBER INDEX.
(1)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Section II and III.
(2)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
(3)
STOCK NUMBER column. This column
lists the NSN for the item.
(4)
CAGEC column. The Commercial And
Government Entity (CAGE) Code (C) is a 5 digit
alphanumeric code used to identify the manufacturer,
distributor or Government agency, etc., that supplies the
item.
(5)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation or Government activity), which
controls the design and characteristics of the item by
means of its engineering drawings, specifications
standards and inspection requirements to identify an
item or range of items.
4
|