 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 10-3930-611-35
1.
Screw, socket hd (6 reqd)
42.
Washer, lock (4 reqd)
2.
Block, stop (2 reqd)
43.
Pad, stop (2 reqd)
3.
Screw, socket hd (16 reqd)
44.
Shim (2 reqd)
4.
Washer, lock (20 reqd)
45.
Screw, socket hd (ref item #3)
5.
Pad, bearing (8 reqd)
46.
Washer, lock (ref item #4)
6.
Shim (as reqd, approx 8 reqd)
47.
Pad, bearing (ref item #5)
7.
Nut, hex (8 reqd)
48.
Shim (ref item #6)
8.
Washer, flat (8 reqd)
49.
Nut, hex (ref item #7)
9.
Screw, flat hd (4 reqd)
50.
Washer, lock (ref item #4)
10.
Pad, bearing (2 reqd)
51.
Washer, flat (ref item #8)
11.
Shim (as reqd, approx 2 reqd)
52.
Screw, flat hd (4 reqd)
12.
Screw, flat hd (24 reqd)
53.
Pad, bearing (2 reqd)
13.
Pad, bearing (4 reqd)
54.
Shim (2 reqd)
14.
Shim (as reqd, approx 4 reqd)
55.
Nut, hex
15.
Mast, telescoping (1st STG)
56.
Washer, lock
16.
Screw, flat hd (ref item #12)
57.
Screw, socket hd
17.
Pad, bearing (8 reqd)
58.
Screw, flat hd (ref item #12)
18.
Shim (as reqd, approx 8 reqd)
59.
Pad, bearing (ref item #13)
19.
Screw, flat hd (ref item #12)
60.
Shim (ref item #14)
20.
Pad, bearing (ref item #17)
61.
Screw, flat hd (ref item #12)
21.
Shim (ref item #18)
62.
Pad, bearing (ref item #17)
22.
Screw, socket hd (ref item #3)
63.
Shim (ref item #18)
23.
Washer, lock (ref item #4)
64.
Screw, flat hd (ref item #12)
24.
Pad, bearing (ref item #5)
65.
Pad, bearing (ref item #17)
25.
Shim (ref item #6)
66.
Shim (ref item #18)
26.
Bolt, hex hd (4 reqd)
67.
Screw, socket hd (ref item #3)
27.
Washer, lock (4 reqd)
68.
Washer, lock (ref item #4)
28.
Brace
69.
Pad, bearing (ref item #5)
29.
Pin, cotter (12 reqd)
70.
Shim (ref item #6)
30.
Pin, idler (6 reqd)
71.
Mast, telescoping (2 STG)
31.
Idler, leaf chain (6 reqd)
72.
Nut, self-locking (2 reqd)
32.
Pin, cotter (ref item #29)
73.
Pin, cotter (4 reqd)
33.
Pin, idler (ref item #30)
74.
Pin, clevis (2 reqd)
34.
Idler, leaf chain (ref item #31)
75.
Clevis (2 reqd)
35.
Stud (4 reqd)
76.
Spacer (2 reqd)
36.
Latch
77.
Nut, jam (2 reqd)
37.
Latch (2 reqd)
78.
Rod (2 reqd)
38.
Stud (ref item #35)
79.
Mast, fixed
39.
Latch
80.
Stud
40.
Latch (ref item #37)
81.
Latch
41.
Screw, socket hd (4 reqd)
Figure 3-12. Mast assembly, disassembly and reassembly.
Section III. HYDRAULIC SYSTEM
3-11. General
e. Installation. Install the stack valve (TM 10-3930-
611-12).
This section provides information useful in the
3-13. Hydraulic Pump
maintenance and repair of the hydraulic system.
3-12. Stack Valve (Control Valve)
a. Removal Remove the stack valve (TM 10-3930-
2).
b. Disassembly.
Refer to figure 3-14 and
611-12).
b. Disassembly.
disassemble the hydraulic pump.
Refer to figure 3-13 and
c. Cleaning, Inspection and Repair.
disassemble the stack valve.
c. Cleaning, Inspection and Repair.
(1) Clean all parts with dry cleaning solvent
(Federal Specification P-D-680) and dry thoroughly.
(1) Clean all parts with dry cleaning solvent
(2) Inspect for shaft seal leakage (possibility of
(Federal Specification P-D-680) and dry thoroughly.
sucking air). Inspect o-rings between sections (external
(2) Inspect for breaks, cracks, bends, loose or
leakage source). Inspect vanes for pitted or chipped
missing mounting hardware, or other defects.
surfaces. Inspect pressure plate for damage. Inspect all
(3) Tighten or replace loose or missing mounting
other parts for breaks, cracks, loose or missing hardware.
hardware, replace a damaged or defective part as
(3) Tighten or replace loose or missing hardware.
necessary.
d. Reassembly.
Replace shaft seals and o-rings if deteriorated or
Refer to figure 3-13 and
damaged.
Replace vanes and/or pressure plate if
reassemble the stack valve.
damage is evident.
3-15
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals