| |
TM 10-3930-609-24P
F -
Direct support or aviation intermediate is
the lowest level than can do complete
repair of the item.
H -
General support is the lowest level that
can do complete repair of the item.
L-
Specialized repair activity is the lowest
level that can do complete repair of the
item.
D-
Depot is the lowest level that can do
complete repair of the item.
Z -
Nonreparable. No repair is authorized.
B-
No repair is authorized. (No parts or
special tools are authorized for the
maintenance of a "B"-coded item.)
However, the item may be reconditioned
by adjusting, lubricating, etc., at the user
level.
(3) Recoverability Code. Recoverability codes are
assigned to items to indicate the disposition action on
unserviceable items. The recoverability code is entered
in the fifth position of the SMR code as follows:
Code
Application/Explanation
Z -
Nonreparable item. When unserviceable,
condemn and dispose of the item at the
level of maintenance shown in the 3d
position of the SMR code.
O -
Reparable item. When uneconomically
reparable, condemn and dispose of the
item at unit maintenance or aviation unit
level.
F -
Reparable item. When uneconomically
reparable, condemn and dispose of the
item at the direct support or aviation
intermediate level.
H -
Reparable item. When uneconomically
reparable, condemn and dispose of the
item at the general support level.
D -
Reparable item. When beyond lower level
repair capability, return to depot.
Condemnation and disposal of item not
authorized below depot level.
L -
Reparable item. Condemnation and
disposal of item not authorized below
specialized repair activity (SRA).
A -
Item requires special handling or
condemnation procedures because of
specific reasons(e.g., precious metal
content, high dollar value, critical
material, or hazardous material). Refer to
appropriate manuals/directives for specific
instructions.
c.
CAGEC (Column (3)). The Commercial and
Government Entity (CAGE) Code (C) is a 5-digit
alphanumeric code which is used to identify the
manufacturer, distributor, or Government agency, etc.,
that supplies the item.
d.
PART NUMBER (Column (4)). Indicates the
primary number used by the manufacturer (individual,
company, firm, corporation, or Government activity),
which controls the design and characteristics of the item
by means of its engineering drawings, specifications
standards, and inspection requirements to identify an
item or range of items.
NOTE: When you use an NSN to requisition an item, the
item you receive may have a different part number from
the part ordered.
e.
DESCRIPTION AND USABLE ON CODE (UOC)
(Column (5)). This column includes the following
information:
(1)
The Federal item name and, when
required, a minimum description to identify the item.
(2) Physical security classification. Not
Applicable.
(3) Items that are included in kits and sets are
listed below the name of the kit or set on Figure KIT.
(4)
Spare/repair
parts
that
make
up
an
assembled item are listed immediately following the
assembled item line entry.
(5)
Part
numbers
for
bulk
materials
are
referenced in this column in the line item entry for the
item to be manufactured/fabricated.
(6) When the item is not used with all serial
numbers of the same model, the effective serial numbers
are shown on the last line(s) of the description (before
UOC). Not Applicable.
(7) The usable on code, when applicable (see
paragraph 5, Special Information).
(8) In the Special Tools List section, the basis of
issue (BOI) appears as the last line(s) in the entry for
each special tool, special TMDE, and other special
support equipment. When density of equipments
supported exceeds density spread indicated in the basis
of
issue,
the
total
authorization
is
increased
proportionately.
(9) The statement "END OF FIGURE" appears
just below the last item description in Column 5 for a
given figure in both Section II and Section III.
f.
QTY (Column (6)). The QTY (quantity per figure
column) indicates the quantity of the item
3
|