Quantcast Steering Spindles and Kingpins

 

Click here to make tpub.com your Home Page

Page Title: Steering Spindles and Kingpins
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 75. Drive shaft, exploded view.
Up
TM-10-3930-222-35 Truck Lift Fork Gasoline Pneumatic-Tired Wheels 15 000-Pound Capacity Manual
Next
Figure 76. Steering axle with center arm, exploded view.
Punch kingpin from bottom until top needle
(4) Remove cotter pin, grease fitting, and end plug,
bearing is removed.
and disconnect power steering cylinder (TM 10-
(5) Remove kingpin from center arm and remove
3930-222-20).
center arm from truck.
(5) Remove cotter pin, end plug, seat and spring,
b. Cleaning, Inspection, and Repair.
and disconnect drag link (TM 10-3930-222-20).
(6) Mark axle support caps (12, fig. 76) and remove
(1) Wash all parts in SD.
four screws (14) and lockwashers (13).
(2) Inspect all parts for wear.
(7) Lower jack slightly, remove two support caps,
(3) Replace defective parts as authorized.
and remove steering axle assembly.
c. Installation Using new needle bearings, reverse
b. Disassembly.
procedures in a above.
(1) Remove tie rods (TM 10-3930-22220).
48.
Steering Spindles and Kingpins
(2) Remove kingpins (par. 48).
a. Removal.
(3) Remove steering center arm (par. 47).
(1) Remove steering wheels (TM 103930-222-20).
c. Inspection. Inspect all parts for excessive wear,
(2) Disconnect tie rods from spindles (TM 10-3930-
cracks, breaks, binds, and mutilations.
222-20).
d. Repair.
(3) Remove spring pin (3, fig. 76) that secures
(1) Where
possible, repair cracked or broken
kingpin (15) to spindle (4).
castings and housings by welding.
(4) Using small punch drive through top needle
(2) Replace defective bearings and other items as
bearing (7) until kingpin pushes lower needle
authorized.
If necessary replace the axle
bearing (16) from spindle.
assembly.
(5) Using small punch drive from bottom of axle
e. Assembly. Reverse procedures in b above.
until kingpin pushes top bearing from spindle.
f. Installation. Reverse procedures in a above.
(6) Drive kingpin from spindle and remove spindle,
bearing (5), and shim (6) from axle assembly.
(7) Repeat procedures above and remove kingpin
47.
Steering Center Arm a. Removal.
on other end of axle if necessary.
(1)
Remove steering axle (par. 46).
b. Cleaning, Inspection, and Repair.
(2)
Remove tie rods (TM 10-3930-22220).
(1) Wash all parts in SD.
(3)
Drive spring pin (21, fig. 76) from kingpin (24) in
(2) Inspect all parts for wear.
center arm.
(3) Replace defective parts as authorized.
(4)
Punch through top needle bearing (17)  until
c. Installation Using new needle bearings, reverse
kingpin  pushes bottom needle bearing (25)
procedures in a above
from center arm.
AOO 7010A
90

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.