|
| |
TM 10-3930-222-24P
4.
Explanation of Columns (Section IV).
a.
NATIONAL
STOCK
NUMBER
(NSN)
INDEX.
(1)
STOCK
NUMBER
column.
This
column lists the NSN by National Item Identification
Number (NIIN) sequence. The NIIN consists of the last
nine
NSN
digits of the NSN (i.e., 5305-01-674-1467).When
NIIN
using this column to locate an item, ignore the first4
digits of the NSN. However, the complete NSN should
be used when ordering items by stock number.
(2)
FIG. column. This column lists the
number of the figure where the item is identified/located.
The figures are in numerical order in Section II and
Section Ill.
(3)
ITEM column. The item number
identifies the item associated with the figure listed in the
adjacent FIG. column. This item is also identified by the
NSN listed on the same line.
b.
PART NUMBER INDEX. Part numbers in
this index are listed by part number in ascending
alphanumeric sequence (i.e., vertical arrangement of
letter and number combination which places the first
letter or digit of each group in order A through Z, followed
by the numbers 0 through 9 and each following letter or
digit in like order).
(1)
CAGEC column. The Commercial and
Government Entity (CAGE) Code (C) is a 5-digit
alphanumeric code used to identify the manufacturer,
distributor, or Government agency, etc., that supplies the
item.
(2)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation, or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards, and
inspection requirements to identify an item or range of
items.
(3)
STOCKNUMBER
column.
This
column lists the NSN for the associated part number and
manufacturer identified in the PART NUMBER and
CAGE columns to the left.
(4)
FIG. column. This column lists the
number of the figure where the Item is identified/located
in Sections II and III.
(5)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
c.
FIGURE AND ITEM NUMBER INDEX.
(1)
FIG. column. This column lists the
number of the figure where the item is identified/located
in Sections II and III.
(2)
ITEM column. The item number is that
number assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
(3)
STOCK
NUMBER
column.
This
column lists the NSN for the item.
(4)
CAGE column. The Commercial and
Government Entity (CAGE) is a 5-digit alphanumeric
code used to identify the manufacturer, distributor, or
Government agency, etc., that supplies the item.
(5)
PART NUMBER column. Indicates the
primary number used by the manufacturer (individual,
firm, corporation, or Government activity), which controls
the design and characteristics of the item by means of its
engineering drawings, specifications standards and
inspection requirements to identify an item or range of
items.
5.
Special Information.
a.
USABLE ON CODE. The usable on code
appears in the lower left corner of the Description column
heading. Usable on codes are shown as "UOC: in the
Description column Justified left) on the first line
following
applicable
item
description/nomenclature.
Uncoded
items
are
applicable
to
all
models.
Identification of the usable on codes used in the RPSTL
are:
Code
Used On
CGY
MHE178
CJG
MHE178A
CJH
MHE178B
CJJ
MHE178C
CGZ
MHE223
b.
FABRICATION
INSTRUCTIONS.
Bulk
materials required to manufacture items are listed in the
Bulk Material Functional Group of this RPSTL. Part
numbers for bulk materials are also referenced in the
Description column of the line item entry for the item to
be
manufactured/fabricated.
Detailed
fabrication
instructions for items source coded to be manufactured
or fabricated are found in TM 10-3930-222-20 and TM
10-3930-222-34.
c.
ASSEMBLY INSTRUCTIONS. Detailed
assembly instructions for items source coded to be
assembled from component spare/repair parts are found
in TM 10-3930-222-20 and TM 10-3930-222-34. Items
that make up the assembly are listed immediately
following the assembly item entry or reference is made to
an applicable figure.
4
|
