 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 KEY
LUBRICANT
EXPECTED TEMPERATURE
INTERVALS
Above +40F
+40F to -10F -10Fto -65 F
D - Daily
(Above +4C)
(+4C to -23C) (-23C to -55C)
50H - 50hours
100 H - 100 hours
OE/HDO
LUBRICATION OIL,
200 H - 200 hours
(MIL-L-2104) INTERNAL
250 H - 250 hours
COMBUSTION ENGINE,
500 H- 500 hours
OEA
COMBAT/TACTICAL
1000 H - 1000
(MIL-L-46167)
hours
LUBRICATING OIL,
OC - On condition
INTERNAL COMBUSTION
ENGINE, ARCTIC
Engine crankcase
OE/HDO-15/40
OEA
Transmission and oil cooler OE/HDO--10
OEA
I
Hydraulic reservoir
OE/HD0 10
OEA
GO
LUBRICATING OIL, GEAR,
(MIL-L-2105) MULTI PURPOSE
Front and rear differrential
GO-80/90
Planetary gear hubs
G-80/90
GAA
GREASE, AUTOMOTIVE
TOTAL
(M)L-G-10924) AND ARTILLERY
MANHOURS
Axle articulation joints,
Interval
Manhour
propeller shafts, mast pivot,
D
.2
tilt cylinder pivot, rotate
ALL TEMPERATURES
50 H
1.2
carriage pin, spine bushing
100 H
.2
200 H
.3
250H
1.5
BFS
BRAKE FLUID, SlLICONE,
250 H
1.5
(MlL-B-46176) AUTOMOTIVE, ALL
1000 H
2.0
WEATHER
OC
2.0
Brake master cylinders,
throttle control reservoir
ALL TEMPERATURES
CT
CORROSION PREVENTIVE
(MIL-C-16173) COMPOUND SOLVENT
CUTBACK, COLD
APPLICATION
Mast chains
ALL TEMPERATURES
SD-2
SOLVENT, DRY CLEANING
ALL TEMPERATURES
(P-D-680)
NOTES
1. TRANSMISSION. If AOAP cannot be performed,
4. DIFFERENTIAL (FRONT AND REAR). Drive vehicle
drain and refill transmission every 250 hours. With
for 10 minutes to warm lubricant. Clean area around
engine running and oil warm check oil level daily and add
drain and fill plugs before removing. After draining install
OE as necessary. Drain only when oil is hot. Refill to H
drain plugs and fill to fill plug opening with GO then install
mark on oil dipstick. Replace oil filter with each oil
plug.
change.
5. PLANETARY GEAR HUBS. With fill/drain plug at six
2.
ENGINE CRANKCASE.
If AOAP cannot be
o'clock position remove plug and drain oil. Rotate
performed, drain and refill crankcase every 250 hours.
fill/drain opening to 3 o'clock position and fill to opening
Check oil level daily and add OE as necessary. Drain
with GO. Install fill/drain plug.
only when oil is hot. Refill to FULL mark on oil dipstick.
6. PROPELLER SHAFTS (FRONT AND REAR). Do not
Run engine 3-5 minutes and recheck level. Add oil as
use high pressure gun on these fittings. Seals will
necessary. Replace oil filter element with each oil
rupture under pressure.
change.
7. SPINE BUSHING. Use sideshift control to position
3. HYDRAULIC RESERVOIR. If AOAP cannot be
spine to the left side s that fitting on spine bushing is
performed, drain and refill reservoir every 500 hours.
accessible through hole in mud guard on rear of sideshift
Check level daily and add OE as necessary. Drain only
carrier. Grease with GAA. Move spine to the right side
when oil is hot. Refill to LOW mark on sight gauge.
so that fitting is accessible through hole in mud guard
Replace filter cartridge with each oil change or when
and grease with GAA again.
pressure indicator on filter head reaches RED zone.
CARD 2 OF 6
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals