Click here to make tpub.com your Home Page

Page Title: ENGINE OIL FILTERS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

NOTES - CONTINUED:
9. DIFFERENTIAL LOCK CONTROL
change oil each 100 hours. Drain when
VALVE. Check level each 100 hours. Oil
lubricant is warm.
should be within 3/4 inch (19 millimeters)
o f the top of valve. Drain only when
r e p a i r e d . Bleed lines at the lockout
6. ENGINE OIL FILTERS. Filters are to
mechanism on the differential. Use BFS
b e replaced each time an engine oil
Brake Fluid (MIL-B-46176) on (S/N E 1468)
change is directed by AOAP laboratory.
and up. Use oil OE/HDO 10 (MIL-L-2104C)
After installing new filter elements, fill
for S/N below S/N 1468.
c r a n k c a s e , operate engine 5 minutes,
check housing for leaks, check crankcase
10. CONSTANT VELOCITY JOINT. After
oil level and bring to "FULL" mark. When
operation in sea water remove a bolt (only
AOAP laboratory support is not available,
1 of 4) from bottom bearing cap, drain off
i n s t a l l new filter elements each 100
water, inject GAA through top fitting to
hours.
remove contaminated lube. Replace bear-
ing cap bolt. Relubricate.
7. TRANSMISSION AND TORQUE CON-
11. DIFFERENTIALS/WHEEL HUBS/
VERTER. Check oil level each ten hours
STEERING GEAR HOUSING. Check level
with engine running at 500-600 RPM and
each 50 hours. Change gear lubricant only
oil temperature at 150F (66C) to 200F
when required by maintenance repair ac-
(93C) with transmission in neutral. Main-
tion, contamination by water, or other
tain oil level to "FULL" mark. Oil is to be
foreign material. After refill, operate for
changed each time a transmission oil
five minutes, check for leaks and bring oil
change is directed by AOAP laboratory.
level to level plug opening.
D r a i n transmission with oil at 150F
(66C) to 200F (93C). Remove sump
s c r e e n , clean and replace using new
12. FRONT WHEEL HUB/REAR WHEEL
g a s k e t . Refill transmission to "FULL"
HUB. To drain, turn wheel until fill and
mark. With engine running at 500 to 600
drain plug is at bottom center. Fill hous-
RPM and oil temperature at 150F (66C)
ing by turning wheel until fill and drain
to 200F (93C) and with transmission in
plug is in an upward position. Check level
n e u t r a l , add oil to bring oil level to
with arrow pointing straight down. Fill un-
" F U L L " mark. When AOAP laboratory
til lubrication extrudes from level plug
support  is  not  available,  change
(lower plug opening).
transmission oil each 500 hours.
13. HYDRAULIC TANK OIL FILTER. Each
500 hours change oil filter or when Filter
Contamination Indicator shows red,
8. TRANSMISSION EXTERNAL FILTER.
whichever occurs first.
F i l t e r is to be replaced each time a
transmission oil change is directed by
14. LUBRICANTS. The following is a list
AOAP laboratory. Remove element, clean
of lubricants with military symbols and
filter housing, install new element and
applicable specification numbers.
seal. After replacement, with engine run-
ning at fast idle, oil temperature at 150F
MIL-L-2104
OE/HDO
(66C) to 200F (93C) and transmission
MIL-L-2105
GO
i n neutral fill transmission to "FULL"
MlL-G-10924
GAA
mark. Operate for five minutes and check
MIL-L-46167
OEA
for leaks. When AOAP laboratory support
FED-VV-751
CW
is not available, install new filter element
MIL-B-46176
BFS
each 500 hours.
P-D-680
(SD), Type II
MIL-G-23549
GGP
TA 219958
CARD 8 OF 9
LO 10-3930-634-12

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business