Click here to make tpub.com your Home Page

Page Title: FOR OPERATION OF EQUIPMENT IN PROTRACTED COLD TEMPERATURES BELOW 150F (-26C)
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

NOTES:
1.
FOR  OPERATION  OF  EQUIPMENT  IN
"FULL" mark.
Operate for 5 minutes and check for
PROTRACTED COLD TEMPERATURES BELOW  -
leaks.
150F (-26C).Remove lubricants prescribed in Key for
temperatures above -15F (-26C). Relubricate with
7.  TRANSMISSION OIL FILTER.  Each 200 hours,
lubricants specified in Key for temperatures below -15F
remove filter element, clean filter housing, install new
(-26C).  If OEA lubricant is required to meet the
filter element and gasket. Fill transmission to low mark.
temperature ranges prescribed in the Key, OEA lubricant
With engine running at idle speed, oil at operating
is to be used in place of OE/HDO-10 lubricant for all
temperature and transmission in neutral, add oil to bring
temperature ranges where OE/HDO-10 is specified in
oil level to "FULL" mark.  Operate for 5 minutes and
the Key.
check filter housing for leaks.
2.
OIL CAN POINTS.
Each 50 hours lubricate
8. HYDRAULIC RESERVOIR.  Each 10 hours check
accelerator and parking brake linkage, mast interlock,
level.  Maintain oil level at "FULL" mark.  Each 1000
and control valve linkage, pins and devises and all
hours, drain, flush and refill reservoir. Operate hydraulic
exposed adjusting threads with OE/HDO.
system for 5 minutes, check for leaks, check oil leval and
bring to "FULL" mark.
3. ENGINE OIL LEVEL HOT OR COLD CHECK. Cold
engine, oil level should be at high mark on dipstick. Hot
9. HYDRAULIC FILTER. Each 200 hours, remove filter
engine, oil level must be between high and low marks on
element, clean filter shell and install new filter element.
dipstick (allow to set 5 minutes before checking).
After replacement, operate hydraulic system for 5
minutes, check for leaks, check oil level and bring to
4. ENGINE. Oil is to be changed each 100 hours. Drain
"FULL" mark.
when lubricant is warm.
10.  BULL GEAR/WHEEL BEARINGS/AXLE SHAFT
5. ENGINE OIL FILTER. Each 100 hours, remove filter
AND BEARINGS.  Each 500 hours remove wheels,
element, clean housing and install new filter element.
clean and. inspect all parts, replace damaged or worn
After installing new filter element, fill crankcase, operate
parts, repack bearings and reassemble.  Fill bull gear
engine for 5 minutes, check housing for leaks, check
spaces to three-fourths height of teeth with GAA grease.
crankcase oil level and bring to "FULL" mark.
11. STEERING WHEEL BEARINGS. Each 500 hours
6. TRANSMISSION. Check level each 100 hours with
remove wheels, clean and inspect all parts, replace
engine running at idle speed, oil at operating temperature
damaged  or  worn  parts,  repack  bearings  and
and transmission in neutral. Maintain oil level at "FULL"
reassemble.
mark. Change oil each 1000 hours. Fill transmission to
low mark. Run engine at idle speed to fill converter and
12. DRIVE AXLE AND DIFFERENTIAL. Check level
lines.  With engine running at idle speed, oil  at
each 100 hours.  Change gear lubricant only when
operating temperature and transmission in neutral, add
required by maintenance repair action, contamination by
oil to bring LO 10-3930-630-12 oil level to
water or other foreign material. After refill, operate for
five minutes, check for leaks and bring oil to "FULL"
mark.
TA 220514
LO 10-3930-630-12 CARD 5 OF 6
NOTES - CONTINUED:

Privacy Statement - Press Release - Copyright Information. - Contact Us