3930-00-958-3682) AND (ALLIS-CHALMERS MODEL FT 20-24PS-127) (NSN 3930-00-958-3683) (ARMY MODEL MHE-182)">

 

Click here to make tpub.com your Home Page

Page Title: UNIVERSAL JOINTS
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

NOTES - CONTINUED:
plug is clean, make sure truck is level and mast is
17. BULL GEARS. Each 1000 operating hours remove
lowered  before  removing  level  plug.
If  oil  is
drive wheels, clean bull gears and dry with compressed
contaminated, drain system and tank and refill with clean
air.  Inspect for damage or excessively worn teeth.
oil. Each 1000 operating hours drain tank, remove and
Lubricate gears sparingly with GAA and Install drive
clean breather element. Remove filter elements, clean
wheels.
filter shells, and install new filter elements. Refill tank
and operate hydraulic system for 5 minutes, check for
18. LUBRICANTS. The following is a list of lubricants
leaks, check oil level, and bring to level plug opening.
with  military  symbols  and  applicable  specification
numbers.
13.  UNIVERSAL JOINTS.  Each 500 operating hours
remove and disassemble universal joints.  Clean and
OEIHDO
MIL-L-2104
inspect all parts, replace damaged or worn parts, repack
OEA
MIL-L-46167
bearings, assemble and install.
GO
MIL-L-2105
BFS
MIL-B-46176
14.  TRANSMISSION AND CONVERTER.  Each 10
GAA
MIL-G-10924
operating hours check oil level with engine running at
PL
MIL-L-3150
idle speed, oil at operating temperature and transmission
PL
VV-L-800
in neutral. Maintain oil level at "FULL" mark. Each 500
(SD), Type II
P-D-680
operating hours drain all oil from transmission and
converter.  Access to converter drain plug is gained
through timing cover opening in engine flywheel housing.
Rotate flywheel until drain plug is in opening, remove
plug and rotate flywheel until plug opening is aligned
with drain opening at bottom of flywheel housing. Refill
transmission to low mark. With engine running at idle
speed, oil at operating temperature, and transmission in
neutral (to fill lines and converter), add oil to "FULL"
Copy of this Lubrication Order will remain with the
mark. Operate for 5 minutes and check for leaks.
equipment at all times, instructions contained herein are
mandatory.
15.  WHEEL BEARINGS.  Each 500 operating hours
remove wheels, clean and inspect all parts, replace
By order of the Secretary of the Army:
damaged or worn parts, repack bearings, assemble and
install.
JOHN A. WICKHAM, JR.
General, United States Army
16.  LIFT CHAINS.  Each 250 operating hours clean
Chief of Staff
chains and brush on coat of OE/HDO 10.  Each 500
operating hours remove chains, clean and dry with
OFFICIAL:
compressed air. Inspect for damage or excessive wear.
Brush on coat of OE/HDO, install and adjust.
ROBERT M. JOYCE
Major General, United States Army
The Adjutant General
DISTRIBUTION:
To be distributed in accordance with DA Form 12-25A,
Operator and Organizational maintenance requirements
for Warehouse Equipment.
TA221984
LO 10-3930-233-12
U.S. GOVERNMENT PRINTING OFFICE: 1984-420-903/278
CARD 6 OF 6

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business